Plumbing Essentials: A Prerequisite for Installing a Bathtub
Plumbing Essentials: A Prerequisite for Installing a Bathtub
Blog Article
They are making a few good annotation about Installing A Bathtub overall in this post beneath.
Mounting a tub isn't precisely rocket science, however it does need strong plumbing, carpentry, and in some cases, tiling abilities. Replacing an old bath tub with a new one is likewise a moderately tough job. If the old tub is readily obtainable, the task can relocate easily; if you have to open a wall surface to remove the old tub as well as place the brand-new tub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will need an assistant to leave the old tub and embeded in the new one. Ensure you have actually certified yourself for the task as well as are comfortable attempting it. As opposed to working with a specialist to take over a halfway-completed job, it is much better to consider using one before you begin. Opportunities are you might need a specialist plumber to make tube links.
This short article will certainly aid you mount a brand-new bathtub in your bathroom if you have actually already acquired a brand-new tub and do not require to transform the arrangement of your previous water pipelines.
Your tools and material list should make up the following:
Planning for the Installation
First of all, the sustaining framework supplied with the bath ought to be fitted (if required) according to the producer's guidelines. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is essential to ensure that if the faucet features a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise practical to fit a supporting plate under the taps device to stop strain on the bathtub.
Fit the adaptable tap connectors to the bottom of the two taps using 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you make use of all of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath ought to currently be ready to be fitted in its last setting.
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your installation, after that the first thing you should do is detach the water. After doing so, switch on the faucets to drain pipes any type of water remaining in the system. The procedure of eliminating the existing faucets can be quite bothersome due to the restricted accessibility that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the continuing to be water that will certainly originate from the pipes. Once the supply pipelines have actually been eliminated, make use of the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing compound.
Prior to carrying on to fit the new faucets, contrast the pipe links on the old taps to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the new faucets to fit.
Installing the Tub
Utilizing both wooden boards under its feet, place the bathtub in the required setting. The wood boards are handy in evenly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 little factors.
The following goal is to make certain that the tub is leveled all round. This can be accomplished by checking the spirit level and adjusting the feet on the bathtub up until the spirit level reads degree.
To set up taps, fit the bottom of the outermost adaptable faucet adapter to the proper supply pipe by making a compression join; after that do the same for the various other faucet.
Switch on the water supply as well as check all joints as well as brand-new pipework for leakages and tighten them if essential. Fill the bathtub and additionally inspect the overflow electrical outlet and also the regular electrical outlet for leakages.
Finally, take care of the bathroom paneling as explained in the producer's user's manual. Tiling and also securing around the tub must wait up until the bath tub has been made use of a minimum of once as this will certainly resolve it right into its last position.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to prevent damages to the string. One end of the adapter fits on the plastic tail of the tap and the various other end provides a link to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly need reducing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the faucet in the installing opening in the bath/basin making sure that the washing machines remain in area between the faucet and also the sink. Safeguard the tap in place with the maker provided backnut. Once the faucet is firmly in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap adapters. The previous kind must be linked to the tap finishes initially, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bathroom satisfies the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to break a rigid seal, creating the water to pass through the wall surface in between the bathroom and the tiling, bring about difficulties with dampness as well as feasible leaks to the ceiling listed below.
You can choose from a variety of coloured sealants to blend in your fixtures and also installations. They are offered in tubes as well as cartridges, and also are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of drenched paper or soft rope. Keep in mind to constantly fill up the bath tub with water prior to securing, to permit the movement experienced when the tub is in usage. The sealant can break fairly very early if you do not take into account this motion before securing.
Conversely, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise quickly readily available on the marketplace. It is a good idea to fit the floor tiles making use of waterproof or waterproof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I have been very interested by How to Install a Bathtub Yourself and I hope you enjoyed reading the entire blog entry. In case you appreciated our blog entry please be sure to pass it around. I recognize the value of reading our article about How to Install a Bathtub.
Schedule A Service Call Report this page